Datasets (DL4)#

The gammapy.datasets sub-package contains classes to handle reduced gamma-ray data for modeling and fitting.

The Dataset class bundles reduced data, IRFs and model to perform likelihood fitting and joint-likelihood fitting. All datasets contain a Models container with one or more SkyModel objects that represent additive emission components.

To model and fit data in Gammapy, you have to create a Datasets container object with one or multiple Dataset objects.

Types of supported datasets#

Gammapy has built-in support to create and analyse the following datasets:

Dataset Type

Data Type

Reduced IRFs

Geometry

Additional Quantities

Fit Statistic

MapDataset

counts

background, psf, edisp, exposure,

WcsGeom or RegionGeom

cash

MapDatasetOnOff

counts

psf, edisp, exposure

WcsGeom

acceptance, acceptance_off, counts_off

wstat

SpectrumDataset

counts

background, edisp, exposure

RegionGeom

cash

SpectrumDatasetOnOff

counts

edisp, exposure

RegionGeom

acceptance, acceptance_off, counts_off

wstat

FluxPointsDataset

flux

None

None

chi2

In addition to the above quantities, a dataset can optionally have a meta_table serialised, which can contain relevant information about the observations used to create the dataset. In general, OnOff datasets should be used when the background is estimated from real off counts, rather than from a background model. The FluxPointsDataset is used to fit pre-computed flux points when no convolution with IRFs are needed.

The map datasets represent 3D cubes (WcsNDMap objects) with two spatial and one energy axis. For 2D images the same map objects and map datasets are used, an energy axis is present but only has one energy bin.

The spectrum datasets represent 1D spectra (RegionNDMap objects) with an energy axis. There are no spatial axes or information, the 1D spectra are obtained for a given on region.

Note that in Gammapy, 2D image analyses are done with 3D cubes with a single energy bin, e.g. for modeling and fitting.

To analyse multiple runs, you can either stack the datasets together, or perform a joint fit across multiple datasets.

Predicted counts#

The total number of predicted counts from a MapDataset are computed per bin like:

\[N_{Pred} = N_{Bkg} + \sum_{Src} N_{Src}\]

Where \(N_{Bkg}\) is the expected counts from the residual hadronic background model and \(N_{Src}\) the predicted counts from a given source model component. The predicted counts from the hadronic background are computed directly from the model in reconstructed energy and spatial coordinates, while the predicted counts from a source are obtained by forward folding with the instrument response:

\[N_{Src} = \mathrm{PSF_{Src}} \circledast \mathrm{EDISP_{Src}}(\mathcal{E} \cdot F_{Src}(l, b, E_{True}))\]

Where \(F_{Src}\) is the integrated flux of the source model, \(\mathcal{E}\) the exposure, \(\mathrm{EDISP}\) the energy dispersion matrix and \(\mathrm{PSF}\) the PSF convolution kernel. The corresponding IRFs are extracted at the current position of the model component defined by \((l, b)\) and assumed to be constant across the size of the source. The detailed expressions to compute the predicted number of counts from a source and corresponding IRFs are given in Instrument Response Functions (DL3).

Stacking Multiple Datasets#

Stacking datasets implies that the counts, background and reduced IRFs from all the runs are binned together to get one final dataset for which a likelihood is computed during the fit. Stacking is often useful to reduce the computation effort while analysing multiple runs.

The following table lists how the individual quantities are handled during stacking. Here, \(k\) denotes a bin in reconstructed energy, \(l\) a bin in true energy and \(j\) is the dataset number

Dataset attribute

Behaviour

Implementation

livetime

Sum of individual livetimes

\(\overline{t} = \sum_j t_j\)

mask_safe

True if the pixel is included in the safe data range.

\(\overline{\epsilon_k} = \sum_{j} \epsilon_{jk}\)

mask_fit

Dropped

counts

Summed in the data range defined by mask_safe

\(\overline{\mathrm{counts}_k} = \sum_j \mathrm{counts}_{jk} \cdot \epsilon_{jk}\)

background

Summed in the data range defined by mask_safe

\(\overline{\mathrm{bkg}_k} = \sum_j \mathrm{bkg}_{jk} \cdot \epsilon_{jk}\)

exposure

Summed in the data range defined by mask_safe

\(\overline{\mathrm{exposure}_l} = \sum_{j} \mathrm{exposure}_{jl} \cdot \sum_k \epsilon_{jk}\)

psf

Exposure weighted average

\(\overline{\mathrm{psf}_l} = \frac{\sum_{j} \mathrm{psf}_{jl} \cdot \mathrm{exposure}_{jl}} {\sum_{j} \mathrm{exposure}_{jl}}\)

edisp

Exposure weighted average, with mask on reconstructed energy

\(\overline{\mathrm{edisp}_{kl}} = \frac{\sum_{j}\mathrm{edisp}_{jkl} \cdot \epsilon_{jk} \cdot \mathrm{exposure}_{jl}} {\sum_{j} \mathrm{exposure}_{jl}}\)

gti

Union of individual gti

For the model evaluation, an important factor that needs to be accounted for is that the energy threshold changes between observations. With the above implementation using a EDispersionMap, the npred is conserved, ie, the predicted number of counts on the stacked dataset is the sum expected by stacking the npred of the individual runs,

The following plot illustrates the stacked energy dispersion kernel and summed predicted counts for individual as well as stacked spectral datasets:

(png, hires.png, pdf)

../../_images/plot_stack.png

Note

  • A stacked analysis is reasonable only when adding runs taken by the same instrument.

  • Stacking happens in-place, ie, dataset1.stack(dataset2) will overwrite dataset1

  • To properly handle masks, it is necessary to stack onto an empty dataset.

  • Stacking only works for maps with equivalent geometry. Two geometries are called equivalent if one is exactly the same as or can be obtained from a cutout of the other.

Joint Analysis#

An alternative to stacking datasets is a joint fit across all the datasets. For a definition, see Glossary.

The total fit statistic of datasets is the sum of the fit statistic of each dataset. Note that this is not equal to the stacked fit statistic.

A joint fit usually allows a better modeling of the background because the background model parameters can be fit for each dataset simultaneously with the source models. However, a joint fit is, performance wise, very computationally intensive. The fit convergence time increases non-linearly with the number of datasets to be fit. Moreover, depending upon the number of parameters in the background model, even fit convergence might be an issue for a large number of datasets.

To strike a balance, what might be a practical solution for analysis of many runs is to stack runs taken under similar conditions and then do a joint fit on the stacked datasets.

Serialisation of datasets#

The various Map objects contained in MapDataset and MapDatasetOnOff are serialised according to GADF Sky Maps. A hdulist is created with the different attributes, and each of these are written with the data contained in a BinTableHDU with a WcsGeom and a BANDS HDU specifying the non-spatial dimensions. Optionally, a meta_table is also written as an astropy.table.Table containing various information about the observations which created the dataset. While the meta_table can contain useful information for later stage analysis, it is not used anywhere internally within gammapy.

SpectrumDataset follows a similar convention as for MapDataset, but uses a RegionGeom. The region definition follows the standard FITS format, as described here. SpectrumDatasetOnOff can be serialised either according to the above specification, or (by default), according to the OGIP standards.

FluxPointsDatasets are serialised as gammapy.estimators.FluxPoints objects, which contains a set of gammapy.maps.Map objects storing the estimated flux as function of energy, and some optional quantities like typically errors, upper limits, etc. It also contains a reference model, serialised as a TemplateSpectralModel.

Using gammapy.datasets#

Examples using gammapy.datasets.MapDataset#

Low level API

Low level API

Fermi-LAT with Gammapy

Fermi-LAT with Gammapy

HAWC with Gammapy

HAWC with Gammapy

Source detection and significance maps

Source detection and significance maps

Ring background map

Ring background map

3D detailed analysis

3D detailed analysis

Basic image exploration and fitting

Basic image exploration and fitting

Event sampling

Event sampling

Sample a source with energy-dependent temporal evolution

Sample a source with energy-dependent temporal evolution

Flux Profile Estimation

Flux Profile Estimation

3D map simulation

3D map simulation

Pulsar analysis

Pulsar analysis

Datasets - Reduced data, IRFs, models

Datasets - Reduced data, IRFs, models

Makers - Data reduction

Makers - Data reduction

Mask maps

Mask maps

Modelling

Modelling

Examples using gammapy.datasets.SpectrumDatasetOnOff#

Point source sensitivity

Point source sensitivity

Spectral analysis of extended sources

Spectral analysis of extended sources

Spectral analysis

Spectral analysis

Spectral analysis with energy-dependent directional cuts

Spectral analysis with energy-dependent directional cuts

1D spectrum simulation

1D spectrum simulation

Multi instrument joint 3D and 1D analysis

Multi instrument joint 3D and 1D analysis

Basic image exploration and fitting

Basic image exploration and fitting

Light curves for flares

Light curves for flares

Pulsar analysis

Pulsar analysis

Datasets - Reduced data, IRFs, models

Datasets - Reduced data, IRFs, models

Fitting

Fitting

Makers - Data reduction

Makers - Data reduction